Gecko [ beriskala.com ]

Name	Size	Permission	Date
assignment.rdoc	11.87 KB	-rw-r--r--	2026-03-26 03:35
calling_methods.rdoc	11.26 KB	-rw-r--r--	2026-03-26 03:35
comments.rdoc	7.32 KB	-rw-r--r--	2026-03-26 03:35
control_expressions.rdoc	16.09 KB	-rw-r--r--	2026-03-26 03:35
exceptions.rdoc	2.16 KB	-rw-r--r--	2026-03-26 03:35
literals.rdoc	15.72 KB	-rw-r--r--	2026-03-26 03:35
methods.rdoc	16.92 KB	-rw-r--r--	2026-03-26 03:35
miscellaneous.rdoc	3.78 KB	-rw-r--r--	2026-03-26 03:35
modules_and_classes.rdoc	8.58 KB	-rw-r--r--	2026-03-26 03:35
operators.rdoc	2.35 KB	-rw-r--r--	2026-03-26 03:35
pattern_matching.rdoc	13.01 KB	-rw-r--r--	2026-03-26 03:35
precedence.rdoc	1.09 KB	-rw-r--r--	2026-03-26 03:35
refinements.rdoc	6.83 KB	-rw-r--r--	2026-03-26 03:35

Rename

= Exception Handling

Exceptions are rescued in a +begin+/+end+ block:

begin
    # code that might raise
  rescue
    # handle exception
  end

If you are inside a method, you do not need to use +begin+ or +end+ unless you
wish to limit the scope of rescued exceptions:

def my_method
    # ...
  rescue
    # ...
  end

The same is true for a +class+, +module+, and +block+:

[0, 1, 2].map do |i|
    10 / i
  rescue ZeroDivisionError
    nil
  end
  #=> [nil, 10, 5]

You can assign the exception to a local variable by using <tt>=>
variable_name</tt> at the end of the +rescue+ line:

begin
    # ...
  rescue => exception
    warn exception.message
    raise # re-raise the current exception
  end

By default, StandardError and its subclasses are rescued.  You can rescue a
specific set of exception classes (and their subclasses) by listing them after
+rescue+:

begin
    # ...
  rescue ArgumentError, NameError
    # handle ArgumentError or NameError
  end

You may rescue different types of exceptions in different ways:

begin
    # ...
  rescue ArgumentError
    # handle ArgumentError
  rescue NameError
    # handle NameError
  rescue
    # handle any StandardError
  end

The exception is matched to the rescue section starting at the top, and matches
only once.  If an ArgumentError is raised in the begin section, it will not be
handled in the StandardError section.

You may retry rescued exceptions:

begin
    # ...
  rescue
    # do something that may change the result of the begin block
    retry
  end

Execution will resume at the start of the begin block, so be careful not to
create an infinite loop.

Inside a rescue block is the only valid location for +retry+, all other uses
will raise a SyntaxError.  If you wish to retry a block iteration use +redo+.
See {Control Expressions}[rdoc-ref:syntax/control_expressions.rdoc] for
details.

To always run some code whether an exception was raised or not, use +ensure+:

begin
    # ...
  rescue
    # ...
  ensure
    # this always runs
  end

You may also run some code when an exception is not raised:

begin
    # ...
  rescue
    # ...
  else
    # this runs only when no exception was raised
  ensure
    # ...
  end